SP67-x

SmartPack™

• SmartLink-III™ System Interface
• Lightweight, modular design
• 3 local relay functions, 4 PWM drivers functions and 2 local input discrete functions
• Power-up state of all relay contacts configurable
• Firmware download capability
• Ability to report status of relays in diagnostic utility software
• Fully Programmable discrete control
• Backlighting control
• Redundancy design for high reliability

The SP67 SmartPack™ connects any DPI Labs remote switch panel into the SmartLink-III™ Cabin Management System. The SP67’s (3) relays and (2) discrete inputs can be used to control a wide variety of local relay functions. Local relay control is not limited to the switch panels connected directly to the SmartPack™; Other remote panels on the aircraft can be configured to access the same relays – no extra wiring required! Due to its compact design, a SmartPack™ can be located very close to the loads it controls, keeping harness weight low and wire runs short, a big plus in the tight confines of today’s corporate aircraft. An added benefit of the SP67 is its Pulse-Width-Modulation capability, used to offer dimming functions for local reading and table lights. The unique redundancy design of the module keeps all local functions online in the event of a bus failure. With the SP67’s firmware download capability, local switch panel controls can be quickly reconfigured, making your customers happy and future expansion of your cabin management system easier than ever before.
 

• Functions as remote electronics for any DPI Labs switch panel series such as the 9000 series
• Lighting Control (on/off/continue dimming) for reading lights, table lights, etc.
• Motorized shade control, Airshow Mode Binary Select
• Any local relay control functions

• All dimensions are in Inch
• Material 5052-H32 Aluminum
• Chem-Film Finish
• Weight 10 OZ

• Operating Voltage: 17 ~ 32 VDC
• Operating Current: 0.2 ~ 0.8 Amps
• Operating Temperature: -10 ~ +55 ºC
• System Interface: SmartLink-III Compliant Firmware Upload Re-configurable
• Connector: D-Sub Series with #4-40 Jackscrew ('P' suffix with Positronic's V3 Tab)
• Relay Output: 2x 5Amps Resistive Form-C Relay Contacts (#6,#7), 1x 2Amps Resistive Form-A Relay Contacts (#5)
• PWM Output: 4x Continues Dimming Lights PWM Driver support up to 10x 494-311 Light Dimming Module per circuit
• Discrete Input: 2x Ground Activate Discrete Inputs, 1mA Source
• Panel Interface: 0.8Amps Max. Remote Panel Interface Power
• Support Function: 22 Keys, 2 Display Drive Capabilities

PIN

FUNCTION

PIN

FUNCTION

PIN

FUNCTION

1

Frame Ground

6

Device ID (HEX bit 0)

11

Device ID (HEX bit 3)

2

Power Input +28VDC

7

Device ID (HEX bit 1)

12

Device ID (HEX bit 4)

3

Power Return (GND)

8

Device ID Return (GND)

13

Device ID (HEX bit 5)

4

SmartLink Data bus – HI

9

SmartLink – Shield (GND)

14

Device ID (HEX bit 6)

5

SmartLink Data bus – LO

10

Device ID (HEX bit 2)

15

Device ID (HEX bit 7)

 J2    D-Sub 25 pin Plug (Male)

PIN

FUNCTION

PIN

FUNCTION

1

HeadPhone Audio Right

14

PWM #2  (GND)

2

HeadPhone Audio Common

15

PWM #2 Data

3

HeadPhone Audio Left

16

Discrete Return (GND)

4

17

Discrete Input #1

5

PWM #1 Data

18

Discrete Input #2

6

PWM #3  (GND)

19

PWM #4  (GND)

7

PWM #3 Data

20

PWM #4 Data

8

Discrete Return (GND)

21

Relay #5 Common

9

Relay #6 Common

22

Relay #5 N.O.

10

Relay #6 N.O.

23

Relay #7 N.C.

11

Reserved

24

Relay #7 Common

12

Relay #6 N.C.

25

Relay #7 N.O.

13

Reserved

–

–

• Frame Ground: Chassis Ground connection using 20AWG hookup wire minimum.
• Power Input and Power Return: Power Pins
• SL3 – HI/LO/SHLD: SmartLink-III™ bus connection, using 22AWG (minimum) Shielded Twisted Pair cable with single ended shield terminated to SHLD pin.
• Multiple Panels “J0” (D-Sub 15 Pin) may be connecting to a single Smart-Pack™ ‘J0’ via parallel ‘Y’ jumper cable (“star” interconnect) assembly.
• All “J0” inter-connects must be shielded. The maximum length per branch shall not be exceed 30’.
• HEADPHONE AUDIO R/COM/L: Connection to Headphone Jack Audio source connection, if so equipped. Triple Twisted Shielded
• If more than one panel is connected do not run headphone trough SmartPack (UNLESS INSTRUCTED TO).
• Relay#5: 2 Amp relay contacts.
• Relay#6, #7: 5 Amp relay form-‘C’ contacts.
• "J1" - pin 4 & pin 5:  Double Twisted Shielded.
• "J2" - PWM Data/GND:  Double Twisted Shielded.

1350 Arrow Highway La Verne CA 91750
Voice (909) 392-5777  Fax (909) 392-0277 http://www.dpilabs.com
Copyright © 2002-2004 DPI Labs, Inc. All rights reserved
All data subject to change without notice.